Filters

Secure Checkout
Free Ground Shipping On All Domestic Orders Over $59
Your Shopping Cart Is Empty

Secure Checkout

SKU: 23286 Estim Penis Play 8mm Conductive Rubber Cock Loop Black


Estim Penis Play 8mm Conductive Rubber Cock Loop Black
Purchase Estim Penis Play 8mm Conductive Rubber Cock Loop Black
  • SKU: 23286 Estim Penis Play 8mm Conductive Rubber Cock Loop Black

  • $15.93 $23.95

    Holiday 2024 Get 30% Off Most Items
    Expires December 23rd: $6.82

    Get an Additional 5% Electro
    Expires December 15th: $1.20

    Shipping Weight: 0.20 pounds

    Quantity in Basket:  None

  • Sign up with your email to be notified when this product is back in stock!

Description

This one features two loops on the side that can be used to thread a cord or elastic through to hold it firmly against your body.

When using conductive rubber cock loops for stimming, you generally only stimulate the dorsal nerves running along the top of the penis. The sensations generated are felt at the glans of the penis. Insulating the top part of a lower cock loop, if it is around the cock and balls, allows you to stim both the Dorsal and Perineal nerves leading to better sensations.

Each cock loop insulator will be printed in my BLACK PLA. This insulator comes with 10"/25cm of 8mm conductive rubber tubing that takes 4mm plugs.

Also included is a small length of 4mm CR that takes 2mm plugs so that it can be used as an adaptor to allow you to use 4mm or 2mm plugs on this one.

Suggestion: Fit the short length of 4mm CR into one end of the loop, and then you can use either a 4mm plug or a 2mm one.

It will be dispatched un-painted but with 8mm conductive rubber tubing already fitted.

The inner hole size is 1mm larger than the CR tubing, this 8mm tubing is a good friction fit, and you don't need the plastic locking clamp to keep it in place once fitted. Just slip it over your cock and tighten it before plugging your 4mm plug into the CR (or use the included 4mm CR to use a 2mm plug).

Dimensions

  • Inner Diameter: 1.5"/3.8cm
  • Hole Diameter: 9mm

Care Instructions

Material

This product is 3D printed in ABS, a very strong plastic with excellent mechanical properties. Once printed I post-process the components using a procedure called vapour smoothing. This uses Acetone vapour to melt and smooth the surface of the prints turning them from rough prints into smooth, shiny prints that are non-porous.

Porosity is one drawback of the 3D printing process as it leaves microscopic holes in the surface of prints that are perfect for bacteria to grow in and hard to clean. Vapour smoothing prints seals these tiny holes and imperfections, leaving the products smooth and sealed.

This is important as it makes cleaning post-play so much easier.

Product Care

After play, simply wash in warm soapy water. Anti-bacterial soap is best. Once body fluids have been washed off, allow the electrode to dry thoroughly before you store it away for later use.

A deep clean can be carried out using Isopropyl Alcohol, and this will kill bacteria and remove body oils.

Never use silicone-based lubes with conductive rubber-based electrodes as the silicone will bond to the conductive rubber, effectively destroying it and insulating it.

How To Use

  1. Place the insulated cock loop around your cock and balls with the plastic insulator on top. Use electrolube to ensure you get good contact between the conductive rubber and your skin.
  2. Attach a plug to one end of the conductive rubber.
  3. For the second electrode, I recommend either a cock loop of self-adhesive monopole pad electrode. Place the electrode either on your glans or just under it.
  4. Attach the second plug to the other electrode.
  5. Plug your cable into your control box and ensure all power levels knobs are set to zero output.
  6. Turn on your power box, select your favourite settings and slowly turn up the power.